CODEWITHSUNDEEP
arduinoavrdudearduino-uno
Mikhail Chuprynski
Mikhail Chuprynski

Reputation: 2493

Mac + Uno + avrdude: stk500_recv(): programmer is not responding

I'm trying to upload .hex file to Arduino. I don't have any problems with uploading code through an IDE (like blink example or any other). The port and board are correct.

So, the problem appears when I try to upload

avrdude -pm328p -carduino -P/dev/tty.usbmodemfd121 -b57600 -D -Uflash:w:grbl_v0_8c_atmega328p_16mhz_9600.hex -v -v -v -v

avrdude: Version 6.1, compiled on Mar 23 2014 at 04:42:55
     Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
     Copyright (c) 2007-2014 Joerg Wunsch

     System wide configuration file is "/usr/local/Cellar/avrdude/6.1/etc/avrdude.conf"
     User configuration file is "/Users/Mikhail/.avrduderc"
     User configuration file does not exist or is not a regular file, skipping

     Using Port                    : /dev/tty.usbmodemfd121
     Using Programmer              : arduino
     Overriding Baud Rate          : 57600
avrdude: Send: 0 [30]   [20] 
avrdude: Send: 0 [30]   [20] 
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00

What I tried:

Upvotes: 16

Views: 45985

Answers (8)

Alexey
Alexey

Reputation: 526

I had the same error, and the problem was that I used pins TX/RX in my schema (you need them to be free when uploading).

Upvotes: 1

Bit-Man
Bit-Man

Reputation: 546

One more reason to fail : wrong bootloader

Recently purchased an Arduino nano and when tried to upload Blink for testing purposes it failed. Because the board was manufactured previously to Jan 2018 just selecting Processor > "ATmega328P (Old Bootloader)" solved the problem (https://www.arduino.cc/en/Guide/ArduinoNano#toc4)

Upvotes: 13

Mikhail Chuprynski
Mikhail Chuprynski

Reputation: 2493

Successfully solved with Hex Uploader.

It is created for flashing .hex files to Arduino for Mac OS.

Options for other OS are described in the grbl documentation.

Upvotes: 1

Brandon Lewis
Brandon Lewis

Reputation: 11

Had the same problem. But my fixed it by going to Tools->Serial Port, then selecting tty.ADR6300-SerialPort

Upvotes: 1

wgwz
wgwz

Reputation: 2769

I had the same problem with my Arduino Uno last night. After banging my head on the wall, I upgraded the Arduino IDE to 1.6.0.. I did this on a Mac OS X, simply by downloading 1.6.0 from the Arduino homepage.

After installing this and then selecting the proper board in my case something like: /dev/tty/usbmodem____ (Arduino Uno)

The error was cured and I could again upload programs without having to do any tricky reset button pressing, i.e. one second after the program uploads hold the reset button for 5 seconds.

Well this is what worked for me hope it works for others!

Upvotes: 0

Docman
Docman

Reputation: 89

What fixed it for me was:

  • Disconnect the USB cable from the Arduino
  • Try to upload your program
  • This will fail and the Arduino app will ask you which USB port to use.
  • I did this twice
  • Then plug in the USB cable to the Arduino
  • Upload you program... succes!

Note: Shortly before I installed the drivers mentioned by Mikhail.

Setup: Mac OS 10.9.5, Arduino.app 1.0.6, Arduino Duemilanove

Upvotes: 8

wolfiem
wolfiem

Reputation: 165

I had same problem with Ardunio Leonardo board. I notice that I forgot to set my board version from IDE. After selecting correct board (Tools --> Board --> Ardunio Leonardo) problem solved.

Upvotes: 1

Arne
Arne

Reputation: 11

I just bought an arduinomonkey nano board from Amazon and ran into this exact problem. I am running Arduino software version 1.0.5 and mac osx version 10.9.4.

I tried many different suggestions (like holding reset as you upload) and none of the worked reliably. In all the documents it states that for Mac no updated USB drivers are needed however, I just downloaded the updated drivers from: http://www.ftdichip.com/Drivers/VCP.htm (2.2.18)

after downloading and launching the FTDI..._10_4_.... file. After it installed, went back to the arduino IDE and uploaded a sketch...it worked perfectly!

Upvotes: 1

Related Questions