Reputation: 7482
What is the best way to unit test a method that doesn't return anything? Specifically in c#.
What I am really trying to test is a method that takes a log file and parses it for specific strings. The strings are then inserted into a database. Nothing that hasn't been done before but being VERY new to TDD I am wondering if it is possible to test this or is it something that doesn't really get tested.
Upvotes: 235
Views: 229214
Reputation: 5341
You can even try it this way:
[TestMethod]
public void ReadFiles()
{
try
{
Read();
return; // indicates success
}
catch (Exception ex)
{
Assert.Fail(ex.Message);
}
}
Upvotes: 16
Reputation: 11
What ever instance you are using to call the void method , You can just use ,Verfiy
For Example:
In My case its _Log
is the instance and LogMessage
is the method to be tested:
try
{
this._log.Verify(x => x.LogMessage(Logger.WillisLogLevel.Info, Logger.WillisLogger.Usage, "Created the Student with name as"), "Failure");
}
Catch
{
Assert.IsFalse(ex is Moq.MockException);
}
Is the Verify
throws an exception due to failure of the method the test would Fail ?
Upvotes: 0
Reputation: 1839
Try this:
[TestMethod]
public void TestSomething()
{
try
{
YourMethodCall();
Assert.IsTrue(true);
}
catch {
Assert.IsTrue(false);
}
}
Upvotes: 34
Reputation: 6258
Void return types / Subroutines are old news. I haven't made a Void return type (Unless I was being extremely lazy) in like 8 years (From the time of this answer, so just a bit before this question was asked).
Instead of a method like:
public void SendEmailToCustomer()
Make a method that follows Microsoft's int.TryParse() paradigm:
public bool TrySendEmailToCustomer()
Maybe there isn't any information your method needs to return for usage in the long-run, but returning the state of the method after it performs its job is a huge use to the caller.
Also, bool isn't the only state type. There are a number of times when a previously-made Subroutine could actually return three or more different states (Good, Normal, Bad, etc). In those cases, you'd just use
public StateEnum TrySendEmailToCustomer()
However, while the Try-Paradigm somewhat answers this question on how to test a void return, there are other considerations too. For example, during/after a "TDD" cycle, you would be "Refactoring" and notice you are doing two things with your method... thus breaking the "Single Responsibility Principle." So that should be taken care of first. Second, you might have idenetified a dependency... you're touching "Persistent" Data.
If you are doing the data access stuff in the method-in-question, you need to refactor into an n-tier'd or n-layer'd architecture. But we can assume that when you say "The strings are then inserted into a database", you actually mean you're calling a business logic layer or something. Ya, we'll assume that.
When your object is instantiated, you now understand that your object has dependencies. This is when you need to decide if you are going to do Dependency Injection on the Object, or on the Method. That means your Constructor or the method-in-question needs a new Parameter:
public <Constructor/MethodName> (IBusinessDataEtc otherLayerOrTierObject, string[] stuffToInsert)
Now that you can accept an interface of your business/data tier object, you can mock it out during Unit Tests and have no dependencies or fear of "Accidental" integration testing.
So in your live code, you pass in a REAL IBusinessDataEtc
object. But in your Unit Testing, you pass in a MOCK IBusinessDataEtc
object. In that Mock, you can include Non-Interface Properties like int XMethodWasCalledCount
or something whose state(s) are updated when the interface methods are called.
So your Unit Test will go through your Method(s)-In-Question, perform whatever logic they have, and call one or two, or a selected set of methods in your IBusinessDataEtc
object. When you do your Assertions at the end of your Unit Test you have a couple of things to test now.
IBusinessDataEtc
object.For more information on Dependency Injection ideas on the Construction-level... as they pertain to Unit Testing... look into Builder design patterns. It adds one more interface and class for each current interface/class you have, but they are very tiny and provide HUGE functionality increases for better Unit-Testing.
Upvotes: 15
Reputation: 136683
If a method doesn't return anything, it's either one of the following
Imperative methods - you can verify if the task was actually performed. Verify if state change actually took place. e.g.
void DeductFromBalance( dAmount )
can be tested by verifying if the balance post this message is indeed less than the initial value by dAmount
Informational methods - are rare as a member of the public interface of the object... hence not normally unit-tested. However if you must, You can verify if the handling to be done on a notification takes place. e.g.
void OnAccountDebit( dAmount ) // emails account holder with info
can be tested by verifying if the email is being sent
Post more details about your actual method and people will be able to answer better.
Update: Your method is doing 2 things. I'd actually split it into two methods that can now be independently tested.
string[] ExamineLogFileForX( string sFileName );
void InsertStringsIntoDatabase( string[] );
String[] can be easily verified by providing the first method with a dummy file and expected strings. The second one is slightly tricky.. you can either use a Mock (google or search stackoverflow on mocking frameworks) to mimic the DB or hit the actual DB and verify if the strings were inserted in the right location. Check this thread for some good books... I'd recomment Pragmatic Unit Testing if you're in a crunch.
In the code it would be used like
InsertStringsIntoDatabase( ExamineLogFileForX( "c:\OMG.log" ) );
Upvotes: 183
Reputation: 20692
Use Rhino Mocks to set what calls, actions and exceptions might be expected. Assuming you can mock or stub out parts of your method. Hard to know without knowing some specifics here about the method, or even context.
Upvotes: 3
Reputation: 1504062
Test its side-effects. This includes:
Of course, there's a limit to how much you can test. You generally can't test with every possible input, for example. Test pragmatically - enough to give you confidence that your code is designed appropriately and implemented correctly, and enough to act as supplemental documentation for what a caller might expect.
Upvotes: 78
Reputation: 43264
Presumably the method does something, and doesn't simply return?
Assuming this is the case, then:
If youy let us know what the method does, I could be more specific.
Upvotes: 5
Reputation: 59375
As always: test what the method is supposed to do!
Should it change global state (uuh, code smell!) somewhere?
Should it call into an interface?
Should it throw an exception when called with the wrong parameters?
Should it throw no exception when called with the right parameters?
Should it ...?
Upvotes: 36
Reputation: 13357
Depends on what it's doing. If it has parameters, pass in mocks that you could ask later on if they have been called with the right set of parameters.
Upvotes: 1
Reputation: 44316
it will have some effect on an object.... query for the result of the effect. If it has no visible effect its not worth unit testing!
Upvotes: 6