CODEWITHSUNDEEP
arduinoubuntu-14.04arduino-unoavrdude
Ricardo T. Macedo
Ricardo T. Macedo

Reputation: 71

Ubuntu + UNO R3 - Avrdude programmer is not responding

I'm trying to use a chinese Arduino-Uno (Uno R3) into an Ubuntu 14.04 but I can't upload my sketch.

When I ran the command:

sudo avrdude -v -v -v -v -c avrisp -p m328p -P /dev/ttyUSB0

I get this result:

avrdude: Version 6.0.1, compiled on Oct 21 2013 at 15:55:32
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "/etc/avrdude.conf"
         User configuration file is "/root/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : /dev/ttyUSB0
         Using Programmer              : avrisp
avrdude: Send: 0 [30]   [20] 
avrdude: Send: 0 [30]   [20] 
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00

avrdude done.  Thank you.

I already try:

  1. Check if the cable and/or connectors does not have microcuts;
  2. Verify the pins RX and TX;
  3. Reset button on the board while the upload;
  4. Follow all the steps described on http://playground.arduino.cc/Linux/Ubuntu.

Can you help me fix this error?

PS: My board is just like this one.

Upvotes: 0

Views: 2996

Answers (1)

KIIV
KIIV

Reputation: 3739

Try to use -c arduino, it toggles DTR to restart MCU and start bootloader for few seconds.

BTW: Reset button must be pressed almost precisely just before retry and it is not as easy as it sounds.

Upvotes: 0

Related Questions