Philip Wee
Reputation: 113
Arduino IDE is able to use avrdude to flash hex file, but command line on ubuntu is unable to
Good day all,
I have an arduino pro micro (Chinese knock off version) with which I am able to flash to with the arduino IDE but I am unable to recreate the same effect with avrdude in the terminal on Ubuntu 16.04
This is what I have observed from the verbose output on the arduino IDE:
Forcing reset using 1200bps open/close on port /dev/ttyACM0
PORTS {/dev/ttyACM0, } / {} => {}
PORTS {} / {/dev/ttyACM0, } => {/dev/ttyACM0, }
Found upload port: /dev/ttyACM0
/home/philip/Desktop/arduino-1.8.5/hardware/tools/avr/bin/avrdude -C/home/philip/Desktop/arduino-1.8.5/hardware/tools/avr/etc/avrdude.conf -v -patmega32u4 -cavr109 -P/dev/ttyACM0 -b57600 -D -Uflash:w:/tmp/arduino_build_182426/strandtest.ino.hex:i
avrdude: Version 6.3, compiled on Jan 17 2017 at 11:00:16
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "/home/philip/Desktop/arduino-1.8.5/hardware/tools/avr/etc/avrdude.conf"
User configuration file is "/home/philip/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/ttyACM0
Using Programmer : avr109
Overriding Baud Rate : 57600
AVR Part : ATmega32U4
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 9000 9000 0x00 0x00
flash 65 6 128 0 yes 32768 128 256 4500 4500 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : butterfly
Description : Atmel AppNote AVR109 Boot Loader
Connecting to programmer: .
Found programmer: Id = "CATERIN"; type = S
Software Version = 1.0; No Hardware Version given.
Programmer supports auto addr increment.
Programmer supports buffered memory access with buffersize=128 bytes.
Programmer supports the following devices:
Device code: 0x44
avrdude: devcode selected: 0x44
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e9587 (probably m32u4)
avrdude: reading input file "/tmp/arduino_build_182426/strandtest.ino.hex"
avrdude: writing flash (5918 bytes):
Writing | ################################################## | 100% 0.45s
avrdude: 5918 bytes of flash written
avrdude: verifying flash memory against /tmp/arduino_build_182426/strandtest.ino.hex:
avrdude: load data flash data from input file /tmp/arduino_build_182426/strandtest.ino.hex:
avrdude: input file /tmp/arduino_build_182426/strandtest.ino.hex contains 5918 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 0.05s
avrdude: verifying ...
avrdude: 5918 bytes of flash verified
avrdude done. Thank you.
Which I have done my best to replicate by using this code:
stty -F /dev/ttyACM0 speed 1200
stty -F /dev/ttyACM0 speed 57600
/home/philip/Desktop/arduino-1.8.5/hardware/tools/avr/bin/avrdude -v -p m32u4 -C /home/philip/Desktop/arduino-1.8.5/hardware/tools/avr/etc/avrdude.conf -c avr109 -P /dev/ttyACM0 -b 57600 -D -U flash:w:layout.hex
To the extent of using the same avrdude file and configuration as the IDE
However, when I do it this way, I face the following error:
/home/philip/Desktop/arduino-1.8.5/hardware/tools/avr/bin/avrdude -v -p m32u4 -C /home/philip/Desktop/arduino-1.8.5/hardware/tools/avr/etc/avrdude.conf -c avr109 -P /dev/ttyACM0 -b 57600 -D -U flash:w:layout.hex
avrdude: Version 6.3, compiled on Jan 17 2017 at 11:00:16
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "/home/philip/Desktop/arduino-1.8.5/hardware/tools/avr/etc/avrdude.conf"
User configuration file is "/home/philip/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/ttyACM0
Using Programmer : avr109
Overriding Baud Rate : 57600
AVR Part : ATmega32U4
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 9000 9000 0x00 0x00
flash 65 6 128 0 yes 32768 128 256 4500 4500 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : butterfly
Description : Atmel AppNote AVR109 Boot Loader
**Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
Found programmer: Id = ""; type =
Software Version = .; Hardware Version = .
avrdude: butterfly_recv(): programmer is not responding
avrdude: butterfly_recv(): programmer is not responding
avrdude: error: buffered memory access not supported. Maybe it isn't
a butterfly/AVR109 but a AVR910 device?**
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude: butterfly_recv(): programmer is not responding
avrdude: error: programmer did not respond to command: leave prog mode
avrdude: butterfly_recv(): programmer is not responding
avrdude: error: programmer did not respond to command: exit bootloader
So my question is, why is the Arduino IDE able to detect the type of programmer when the exact same avrdude executable is run through the terminal and yet is unable to flash the hex file?
My best bet is that it has something to do with the forced reset using the baud rate and that the arduino IDE is doing it differently from me, but I am unsure of what I need to change
Any help is greatly appreciated! Thank you.
Upvotes: 1
Views: 1542
Answers (1)
Philip Wee
Reputation: 113
Darn I fixed it within 5 seconds of posting the question, heres how I did it
Instead of using the baud rate to reset it I pressed the reset switch and run the exact same code
So the error is here
stty -F /dev/ttyACM0 speed 1200
stty -F /dev/ttyACM0 speed 57600
But I am not sure what exactly about it is wrong, and clarification would be appreciated anyway :)
Upvotes: 0
Related Questions
- Arduino Nano - "avrdude: ser_open():system can't open device "\\.\COM1": the system cannot find the file specified"
- AVRDUDE command line can't connect to programmer for Leonardo
- Having problem to install avrdude on macOS Terminal
- Why can't I put command in ATMEGA64A-AU serial?
- Uploading Arduino hex file using avrdude
- avrdude: can't handle ELF file checkio.hex, ELF file support was not compiled in
- Avrdude .hex with Fuses
- reading the hex file of atmega8
- Flash .Hex File To Arduino Via Terminal Without AVRDUDE
- AVR-GCC Flashing executable does nothing, flashing the object file directly works