CODEWITHSUNDEEP
arduinostm32clockspi
Hugo Pontes
Hugo Pontes

Reputation: 55

Problems sending SPI Data from STM32 to arduino

I'm trying to learn how to communicate via SPI with STM32 but I've run into some problems.

The first step i took was to implement SPI communications using two arduino unos: the master writes a byte and the slave responds with another byte according to the input (when the master sends anything, triggering the exchange). Everything worked as it should to the best of my knowledge.

The second step is the one I'm stuck at which is to replace the master arduino with a NUCLEO-F767ZI board. I've set up SPI1 using the auto generated code for now, and I've set it up with what I think are the default options. In the main, I send a single byte to the arduino, and this is where the problem starts: By using the serial port in the arduino I can see that it does receive data, but usually bit shifted. So if I send a 16, i usually get a 32 or other power of two in the arduino (see attached image)enter image description here

I'm using clock polarity 0 and clock phase 0 on both microcontrollers (so clock idle on low and sampling on the rising edge). Just to be sure I've tried all possibilities but to no avail, it still doesn't work properly, and I don't really know why. Another thing I considered was that perhaps the clock is running too fast (the peripheral clock is set to 16 MHz), but if I change the prescaler to anything other than SPI_BAUDRATEPRESCALER_2, i stop getting any data on the arduino, only 0s, which I find odd, I would expect it to work just the same if only the master controls the clock.

Just for completeness, here are the spi settings I'm using:

  hspi1.Instance = SPI1;
  hspi1.Init.Mode = SPI_MODE_MASTER;
  hspi1.Init.Direction = SPI_DIRECTION_2LINES;
  hspi1.Init.DataSize = SPI_DATASIZE_8BIT;
  hspi1.Init.CLKPolarity = SPI_POLARITY_LOW;
  hspi1.Init.CLKPhase = SPI_PHASE_1EDGE;
  hspi1.Init.NSS = SPI_NSS_HARD_OUTPUT;
  hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;
  hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB;
  hspi1.Init.TIMode = SPI_TIMODE_DISABLE;
  hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
  hspi1.Init.CRCPolynomial = 7;
  hspi1.Init.CRCLength = SPI_CRC_LENGTH_DATASIZE;
  hspi1.Init.NSSPMode = SPI_NSS_PULSE_DISABLE;

The arduino slave code (I've removed the reply part for now):

void setup (void)
{
  pinMode(MISO, OUTPUT);
  Serial.begin(115200);

  // turn on SPI in slave mode
  SPCR |= _BV(SPE);

  // turn on interrupts
  SPCR |= _BV(SPIE);

 //Check arduino SPI settings, outputs 11000000, so CPHA and CPOL = 0
 Serial.println("SPCR");
 Serial.println(SPCR,BIN);

}  // end of setup

void loop(void){

}

// SPI interrupt routine
ISR (SPI_STC_vect)
{
  byte c = SPDR;
  Serial.println(c);
  } 

}

STM32 master code (ommiting irrelevant parts):

MX_SPI1_Init();
uint8_t data = 16;

  while (1)
  {
      HAL_SPI_Transmit(&hspi1, &data, 1, 100);
      HAL_Delay(500);
  }

Does anyone have a clue as to why this could be happening? I've found nothing on the prescaler issues and all bitshifting issue posts say that the problem is with clock phase or polarity discrepancies, which I've verified is not. Thanks in advance

Upvotes: 0

Views: 1105

Answers (1)

Flexz
Flexz

Reputation: 706

  1. SPI clock rate input to Atmega328P should be lower than Fosc/4
  2. SPI requires the use of nCS wire. An SPI slave will reset it's logic on deassertion of nCS, but if nCS is always at a low level - any missed clock pulse would propagate to the next transfer, shifting the data.

Stm32F7 has NSSP: NSS pulse management - the option for issuing CLK pulse between data bytes. To deassert nCS pin between larger transfers SPI shoud either be disabled and then reenabled before the next transfer, or nCS management should be implemented in the software. In a later case make sure to deassert nCS only after all CLK pulses are completed.

  1. Arduino UNO have Atmega powered from 5V, Stm32 is powered from 3V (on some boards it's 3.3V). Logic high input minimum for the Atmega328 is 0.6VCC, 5V * 0.6V = 3V, wich is on the edge. See this question

A scope would help a lot to solve such cases.

Upvotes: 1

Related Questions